This is the Futaba 9-Channel FM aircraft radio. **also has PCM capabilities**
It has an 8 model memory, and the included CAMpac (FUTM9405) Data Storage. Module increases the memory to 14 models. This radio comes with Futaba's 8-channel R148DF receiver.

*THIS RADIO INCLUDES PROGRAMMING FOR AIR, HELI AND GLIDER MODELS**
**THIS RADIO HAS THE ABILITY TO DO TRIPLE RATES. SEE COMMENTS**

This radio has a memory backup chip, which enables it to keep the radio
settings when the transmitter battery is removed for cycling. 9 channel operation (SEE COMMENTS)

********* New Features Over The 8U* SUPER *************

****PHYSICALLY ---
Easy-Program Dial to speed and simplify programming.
2 Sliders in addition to the 3 dials. normal modes.
A ninth, switch only, channel (available only with 9Channel PCM rcvrs)
No snap direction switches on the radio's face. (see features for details)
New smaller trainer port (cords avail. for 9C to 9C and 9C to older style)
Larger visual display for ease of use, with graphs.
Image of model type visible on screen.
3 Timers, always visible on home screen.

***ALL MODEL TYPES PROGRAMMING:
Menus for basic and advanced rather than scroll-through style. Addition of Aux-Ch functions to assign what controls channels 5-9. Addition of Servo Display and Test function to see servo commands on screen. Increase model name to 10-character. TRIPLE RATES available by assigning dual rates to one of the 2 3-pos. switch Graphical display for curves, dual rates, etc. Dual Rates assignable to all 8 switches, including 3-position for triplerate Dual rate/expo together on a single curve for easy programming. CANNOT reverse trim display colors on screen. Idle-down function is programmable to any switch. FailSafe settings default to a low throttle setting, not "hold" Programmable mixes allow a slider/dial/switch as the primary control of a mix (for inflight adjustment, for example, of airbrakes deployment).

***ACRO PROGRAMMING:
Elev-to-flap preprogrammed mix may be turned on/off in flight with a switch.
Has 0 through 4 separate snaps available, with selection of which snap you are commanding assigned to any 2 switches.

***GLIDER PROGRAMMING:
Has no idle down or throttle cut programming. Elev-to-flap mix has option to turn on/off with any switch. Start & Speed Offset programs both incl. dial to adjust the entire setting 2-FLP glider programming: Flap-to-ail mix incl offset and can assign to any switch, not just D Ail-to-flap mix can be assigned to any switch.

***HELI PROGRAMMING:
No invert mode, no invert offset. Has 3 idle ups, not just 2. Adjust all 4 thr. curves on a single screen. Program offsets1 and 2 on a single screen.
Has 3 revo mixes - 1 for normal, 1 for idles 1 and 2, 1 for idle 3. Has not only 2 linear mixes but also a single 5-point curve mix. Select Hover throttle and pitch adjustment dials (5 choices), including direction. Gyro programming includes condition option, setting a different gyro setting for each of the 5 conditions, OR can assign to any switch, incl 3 position switches which then have 3 settings. (8U had no way to set a gyro setting just for throttle hold.)
Governor programming assign to any switch, incl sep settings for cut channel DOES NOT have a setting for throttle hold. Thr-needle programming has 3 curves - NORM, Idle1/2 and Idle3, but no acceleration option (8U had only 1 curve).

FEATURES:
AIRCRAFT BASIC FUNCTIONS:
Model menu with: Select Model Copy Model Name Parameter menu with: Reset Modulation (FM/PCM select) Model Type Throttle ATL trim option (trim affects low). Second aileron option to use 5-ch receivers Dual Rates and Exponential on a single screen/graphical display End Point Adjustment (ATV) Servo Reversing FailSafe (PCM) Subtrims Trm menu with: Steps Trim Reset Idle-Down (not in GLID) Throttle Cut (not in GLID) 3 Timers Aux Channel function to easily select what controls channels 5-9 Trainer with FUNC option to allow student to use 9C's programming.

AIRCRAFT ADVANCE FUNCTIONS:
Wing types: Flaperon/flap trim (2 wing servos, ch's 1&6, can move as flaps)
Aileron Differential (2 wing servos, ch'2 1&7, no flap movement)
AIL2 provides the option to use a 5-ch servo with either.
Tail types: Elevon (flying wing, 2 servos, operate together as ail & elev)
Ailevator (2 elevator servos, chs 2&8, can move as ailerons)
V-tail (2 angled tail surfaces, 2 servos, move as elev & rud)
Snap Roll function with up to 4 separate snaps selectable in flight
Programmable mixes: elevator-to-flap Airbrake/Crow
throttle-needle Throttle Delay
5 programmable linear mixes (2 for heli)
2 programmable curve mixes (1 for heli)

GLIDER ADVANCE FUNCTIONS DIFFERENT FROM ACRO:
Programmable mixes: flap-to-aileron (GLID2 only) Ail-to-flap (GLID2 only)
start and speed offsets HELI BASIC FUNCTIONS IN ADDITION TO ABOVE:
SWASH AFR (adjust surface direction/travel for CCPM heli types)
4 heli swashplate types:
1 servo per motion, standard = swh1
2 servo, European standard, elev operates on mech linkage CCPM = swh2
4 servo = swh4
3 servos, 2 servos sharing pitch/roll (120 w/ elev to back) = SR-3
3 servos, working together (120 w/ aileron to the side) = SN-3
EASY ADJUSTMENT of Throttle, pitch and revo for NORMAL flight condition
Throttle Cut with specialized heli programming.
HELI ADVANCE FUNCTIONS IN ADDITION TO ABOVE:
5 conditions -- normal, idle ups 1, 2, 3 and throttle hold. Easy adjustment of throttle, pitch and revo for all conditions. Hovering adjustments: hovering pitch and hovering throttle. Gyro specific programming with option to have one setting per each condition Governor programming with separate optional cutoff switch assignment. Trim offsets available for each individual condition.
Delay available to ease transitions from one condition to another.

INCLUDES:
One TX 9CAP (repair switches avail*) No Number
One TX Frequency Module FPTPFM FUTL15**
One RX FP-R148DF Micro RX (Dual Conversion) FUTL73**
One Receiver Crystal (Dual Conversion) FUTL50** 50MHz (or)
FUTL57** 72MHz Lo
FUTL58** 72MHz Hi
One CAMpac Data Storage Module FUTM9405
Four S3004 Servos FUTM0004
One RX Battery FUTM1280
One TX Battery NT-8s700B FUTM1460
(can also use the NT-8S TX battery) *FUTM1457
One Charger FBC-6B(4) FUTM1820
One Frequency flag with numbers No Number
One Aileron extension
One Mini switch harness with charge cord
Three Six-star horns FUTM2010
Two Four-star horns FUTM2030
Twenty Rubber square grommets FUTM2320
Twenty Brass servo eyelets FUTM3650
Twenty Silver mounting screws FUTM2250
Four Small servo wheels (Mounted on the servos) FUTM2020
One Instruction manual
One TX Antenna FUTM5110

OPTIONAL:
*See FUTM3675 for replacement switches available.
*FUTM4244 DSC Cord (This will ONLY work if you PURCHASE the
R149DP or R309DPS receivers)
*FUTM4415 9C to 9C Trainer Cord
*FUTM4420 9C to other Trainer Cord
*FUTM5695 Rubber Hand Grips
*FUTM3640 Heavy Duty Gimbal Springs
COMMENTS:
1)The 2nd Ail Out feature allows a modeler using a 5 channel radio to use twin aileron servos. In the past the flaperon function required the 2nd aileron servo lead to be plugged into channels 6 or 7. Now in the parameters menu the modeler can select 2nd ail out to be 5 or 6/7.

2)The FS change means that if you do not make your own settings for the throttle servo in the PCM settings it will default to a high idle in the event of a PCM lock. PCM RXs: IMPORTANT!! The older 512 PCM resolution rxs are AMC 10/11/01 NOT compatible with this transmitter. For example, DO NOT ir/jl
attempt to use R128DP receiver with this TX, it is the wrong input resolution and will not function properly.

*** The 9th channel on the 9C is an on/off switch ONLY, which is also ONLY
accessible in PCM MODE!! ****

DIFFERENCES BETWEEN 9CA AND 9CH TRANSMITTERS:
9CH has trainer and 2-position switches on top right
9CA has trainer and 2-position switches on top left
9CH has a smooth throttle transition
9CA has ratcheted throttle
COMMENTS: Update pages available at: www.futabarc.com/faq/faq-9c.html. ir/kh. Extensive additional programming/use help available there as well.
Added 9C info is available by visiting the Futaba Support Forum at
www.rcuniverse.com

volver a la página inicial - volver a radios